A skid steer that sits with a flat is not earning anything. On demolition, scrap, recycling, and paving jobs, air-filled tires pick up rebar, nails, and glass faster than most operators can patch them. Airless tires remove the problem. The question is which kind: a molded solid tire, or a standard tire filled with polyurethane foam.
What Airless Actually Means
Two products get called airless, and they behave differently.
A solid skid steer tire is molded rubber all the way through. Most are pressed onto a steel rim at the factory and sold as a complete tire-and-wheel assembly in the machine's bolt pattern and offset. Many have apertures, the rows of holes molded into the sidewall, that let the tire flex and take some harshness out of the ride. Smooth versions have no holes and sit lower and firmer.
A foam-filled skid steer tire starts as a normal pneumatic tire. The valve core is removed, a two-part polyurethane liquid is pumped in under pressure until it displaces the air, and the fill cures into a solid elastomer that holds the tire at roughly its rated pressure. The tread, casing, and size are whatever the original tire was. The air is simply gone.
Neither one needs air, neither one can go flat from a puncture, and neither one can be re-inflated or patched later. That is the point.
Where Solid Tires Win
Solid tires are the right call when the surface is hard and the debris is sharp. Scrap yards, demolition sites, recycling floors, and foundries chew through foam-filled casings because the rubber around the fill still cuts and chunks. A solid tire has far more rubber to lose before it reaches the end of its service life, and nothing inside to expose.
They also last longer in hours. A molded solid typically runs well past what a pneumatic or foam-filled tire of the same size will deliver on abrasive ground, which matters on machines that run two shifts.
The tradeoffs are weight and ride. A set of four solids adds several hundred pounds to the machine compared with pneumatics. That extra mass lowers the center of gravity and improves rearward stability, which some operators like, but it also puts more load on axles and hydraulics and burns more fuel. Without apertures the ride on broken concrete is punishing. Tread options are narrower too: smooth, traction, and all-terrain patterns cover most of the solid market, with far fewer choices than pneumatic catalogs offer.
Where Foam Fill Wins
Foam fill is the better fit when the job mixes surfaces. A grading contractor moving between dirt, gravel, and finished pavement wants a real tread pattern and a ride that does not rattle the cab. Foam fill keeps both. The tire looks and drives like the pneumatic it was, minus the flats.
It also works with the wheels already on the machine. There is no new assembly to match to a bolt pattern, and any tread the manufacturer makes in that size can be filled, including bar lugs for mud, block patterns for mixed use, and non-marking compounds for finished floors.
Foam-filled tires weigh less than solids but considerably more than air-filled tires. The fill wears at the rate of the original tread, so service life is similar to a pneumatic that never went flat, not extended like a solid. And once a casing is cut deep enough to expose the fill, that tire is finished.
The other factor is cure time. Freshly filled tires need to sit before they can carry a load, usually a day or more depending on the fill and the temperature. That is downtime unless the tires are swapped as pre-filled, pre-cured assemblies.
Matching the Tire to the Work
Three questions settle most decisions.
- What is the worst surface the machine sees regularly? Constant sharp debris on hard ground points to solid. Occasional puncture risk on mixed ground points to foam fill.
- Does the added weight matter? Machines working near rated operating capacity, or on soft ground where flotation counts, are better served by the lighter foam-filled option.
- How many hours a week does it run? High-hour machines on abrasive surfaces recover the longer life of a solid. Lower-hour machines rarely wear out either option before the job changes.
Operators also ask whether turf and landscape work belongs here. Usually not. Soft, finished ground is where pneumatic tires still make sense, since the puncture risk is low and the lighter footprint protects the surface.
Sizes and Fitment
The two most common skid steer sizes are 10-16.5 and 12-16.5, and both are available as solids and as fillable pneumatics. The first number is section width in inches and the second is rim diameter. Solid assemblies must also match the wheel's bolt pattern, usually eight lugs on compact loaders, and its offset so the tire sits in the same position under the arms. Swapping to a solid with the wrong offset changes track width and can rub the frame.
Foam fill avoids that entirely because the existing wheel stays. The only fitment check is the tire itself.
Getting Them on the Machine
Georgia Industrial Tire installs both options on site across metro Atlanta and North Georgia. Mobile trucks carry hydraulic presses for solid tire and wheel work, and the foam fill service handles pneumatic casings in place. For fleets that cannot wait on cure time, the assembly exchange program delivers pre-filled, fully cured tire-and-wheel sets and takes the old ones away for EPD-compliant disposal, so the machine is back to work the same visit. Call 770.446.6467 to talk through surface, size, and duty cycle before the next set goes on.